EurekaMag
+ Most Popular
Cunninghamia lanceolata plantations in China
Mammalian lairs in paleo ecological studies and palynology
Studies on technological possibilities in utilization of anhydrous milk fat for production of recombined butter-like products
Should right-sided fibroelastomas be operated upon?
Large esophageal lipoma
Apoptosis in the mammalian thymus during normal histogenesis and under various in vitro and in vivo experimental conditions
Poissons characoides nouveaux ou non signales de l'Ilha do Bananal, Bresil
Desensitizing efficacy of Colgate Sensitive Maximum Strength and Fresh Mint Sensodyne dentifrices
Administration of fluid by subcutaneous infusion: revival of a forgotten method
Tundra mosquito control - an impossible dream?
Schizophrenia for primary care providers: how to contribute to the care of a vulnerable patient population
Geochemical pattern analysis; method of describing the Southeastern limestone regional aquifer system
Incidence of low birth weights in a hospital of Mexico City
Tabanidae
Graded management intensity of grassland systems for enhancing floristic diversity
Microbiology and biochemistry of cheese and fermented milk
The ember tetra: a new pygmy characid tetra from the Rio das Mortes, Brazil, Hyphessobrycon amandae sp. n. (Pisces, Characoidei)
Risk factors of contrast-induced nephropathy in patients after coronary artery intervention
Renovation of onsite domestic wastewater in a poorly drained soil
Observations of the propagation velocity and formation mechanism of burst fractures caused by gunshot
Systolic blood pressure in a population of infants in the first year of life: the Brompton study
Haematological studies in rats fed with metanil yellow
Studies on pasteurellosis. I. A new species of Pasteurella encountered in chronic fowl cholera
Dormancy breaking and germination of Acacia salicina Lindl. seeds
therapy of lupus nephritis. a two-year prospective study

Basic analysis of mechanism in wood cutting. Stress analysis in orthogonal cutting parallel to grain


Basic analysis of mechanism in wood cutting. Stress analysis in orthogonal cutting parallel to grain



Mokuzai Gakkaishi Journal of the Japan Wood Research Society 19: 7-12



ISSN/ISBN: 0021-4795

Studies the critical stress for failure and its point of action in relation to the type of chip formed and surface quality in cutting the wood of Betula maximowicziana. The type of chip formed depends on the relation of the specific cutting force to the crushing strength of the wood. The stress perpendicular at the cutting edge was calculated.

Please choose payment method:






(PDF emailed within 1 workday: $29.90)

Accession: 000027763

Download citation: RISBibTeXText

Related references

Basic analysis of mechanism in wood-cutting. Analysis of cutting energy in orthogonal cutting parallel to grain. Mokuzai Gakkaishi Journal of the Japan Wood Research Society 20(2): 77-82, 1974

Basic analysis of mechanism in wood-cutting. Chip deformation in orthogonal cutting (90-0). Mokuzai Kogyo Wood Industry 27(5): 14-17, 1972

An analysis of cutting work in peripheral milling of wood. II. The cutting force, power and energy requirements in up-milling parallel to wood grain. J. Jap. Wood Res. Soc 16(1): 1-9, 1970

Effects of cutting speed on chip formation and cutting resistance in cutting of wood parallel to the grain. Mokuzai Gakkaishi Journal of the Japan Wood Research Society 25(1): 22-29, 1979

Acoustic emission monitoring of wood cutting. III. Effect of cutting angle on AE characteristics in cutting parallel and perpendicular to the grain. Mokuzai Gakkaishi = Journal of the Japan Wood Research Society 36(4): 269-275, 1990

Studies on mechanism of orthogonal cutting of wood with Japanese plane. I. Effects of distance between knife edge and cap iron edge and depth of cut on surface quality in cutting against the grain. Mokuzai Gakkaishi Journal of the Japan Wood Research Society 23(2): 82-88, 1977

Recognition of wood cutting conditions through cutting sounds I. Effects of tool system's stiffness and tool wear on the generation of sound in cutting parallel to the grain. Mokuzai Gakkaishi = Journal of the Japan Wood Research Society 39(5): 521-528, 1993

Measurements of acoustic emissions in wood cutting with a super surfacer II. Effects of cutting speed and bias angle on acoustic emission characteristics in cutting parallel and perpendicular to the grain. Mokuzai Gakkaishi = Journal of the Japan Wood Research Society 39(6): 724-728, 1993

Studies on mechanism of orthogonal cutting of wood with Japanese plane. II. Chip discharge in cutting without cap iron. Mokuzai Gakkaishi Journal of the Japan Wood Research Society 23(6): 273-279, 1977

Variation of cutting force and frictional coefficient in oblique cutting of wood parallel to the grain. Journal of the Japan Wood Research Society 30(10): 819-826, 1984

Studies on mechanism of orthogonal cutting of wood with Japanese plane. III. Chip discharge in cutting with knife accompanied with cap iron. Mokuzai Gakkaishi Journal of the Japan Wood Research Society 23(8): 361-369, 1977

An analysis of cutting work in peripheral milling of wood. III. Variation of cutting force in inside cutting of wood with router-bit. IV. The power requirement in inside cutting of wood with router-bit. J. Jap. Wood Res. Soc 17(10): 437-48, 1971

The wear characteristics of a woodworking knife with chromium plating III. The self-sharpening characteristics in orthogonal cutting of wood parallel to the grain. Mokuzai Gakkaishi = Journal of the Japan Wood Research Society 37(11): 1004-1010, 1991

Tool life in the cutting of wood by a super surfacer II. Analysis of high efficiency range of cutting speed based on fractures of the cutting edge. Mokuzai Gakkaishi Journal of the Japan Wood Research Society 34(8): 676-681, 1988

Fundamental studies on mechanism of veneer cutting. V. Numerical analysis of stress distribution in workpiece during cutting without pressure bar. Mokuzai Gakkaishi Journal of the Japan Wood Research Society 20(6): 250-256, 1974