EurekaMag
+ Most Popular
Cunninghamia lanceolata plantations in China
Mammalian lairs in paleo ecological studies and palynology
Studies on technological possibilities in utilization of anhydrous milk fat for production of recombined butter-like products
Should right-sided fibroelastomas be operated upon?
Large esophageal lipoma
Apoptosis in the mammalian thymus during normal histogenesis and under various in vitro and in vivo experimental conditions
Poissons characoides nouveaux ou non signales de l'Ilha do Bananal, Bresil
Desensitizing efficacy of Colgate Sensitive Maximum Strength and Fresh Mint Sensodyne dentifrices
Administration of fluid by subcutaneous infusion: revival of a forgotten method
Tundra mosquito control - an impossible dream?
Schizophrenia for primary care providers: how to contribute to the care of a vulnerable patient population
Geochemical pattern analysis; method of describing the Southeastern limestone regional aquifer system
Incidence of low birth weights in a hospital of Mexico City
Tabanidae
Graded management intensity of grassland systems for enhancing floristic diversity
Microbiology and biochemistry of cheese and fermented milk
The ember tetra: a new pygmy characid tetra from the Rio das Mortes, Brazil, Hyphessobrycon amandae sp. n. (Pisces, Characoidei)
Risk factors of contrast-induced nephropathy in patients after coronary artery intervention
Renovation of onsite domestic wastewater in a poorly drained soil
Observations of the propagation velocity and formation mechanism of burst fractures caused by gunshot
Systolic blood pressure in a population of infants in the first year of life: the Brompton study
Haematological studies in rats fed with metanil yellow
Studies on pasteurellosis. I. A new species of Pasteurella encountered in chronic fowl cholera
Dormancy breaking and germination of Acacia salicina Lindl. seeds
therapy of lupus nephritis. a two-year prospective study

Measurements of acoustic emissions in wood cutting with a super surfacer I. Effects of bias angle, tool wear, and knots on acoustic emission characteristics


Measurements of acoustic emissions in wood cutting with a super surfacer I. Effects of bias angle, tool wear, and knots on acoustic emission characteristics



Mokuzai Gakkaishi = Journal of the Japan Wood Research Society 38(3): 241-246



ISSN/ISBN: 0021-4795

In this study, the acoustic emission (AE) signal generated in wood cutting with a super surfacer was measured, and the effects of the bias angle, tool wear, and knots on the AE signal were investigated.

Please choose payment method:






(PDF emailed within 1 workday: $29.90)

Accession: 002652549

Download citation: RISBibTeXText

Related references

Measurements of acoustic emissions in wood cutting with a super surfacer II. Effects of cutting speed and bias angle on acoustic emission characteristics in cutting parallel and perpendicular to the grain. Mokuzai Gakkaishi = Journal of the Japan Wood Research Society 39(6): 724-728, 1993

Acoustic emission characteristics in wood cutting, I. Effects of the grain angles on the amplitudes of acoustic emissions. Mokuzai Gakkaishi = Journal of the Japan Wood Research Society 41(4): 373-379, 1995

Acoustic emission monitoring of wood cutting. III. Effect of cutting angle on AE characteristics in cutting parallel and perpendicular to the grain. Mokuzai Gakkaishi = Journal of the Japan Wood Research Society 36(4): 269-275, 1990

Acoustic emission monitoring of wood cutting I. Detection of tool wear by AE signals. Mokuzai Gakkaishi Journal of the Japan Wood Research Society 34(3): 207-213, 1988

Acoustic emission monitoring of wood cutting II. Effect of slope angle of grain on AE characteristics. Mokuzai Gakkaishi Journal of the Japan Wood Research Society 34(3): 271-274, 1988

Acoustic emission monitoring of wood cutting IV. Effects of moisture content and species on AE characteristics in wood cutting. Mokuzai Gakkaishi = Journal of the Japan Wood Research Society 36(9): 717-724, 1990

Tool life in the cutting of wood by a super surfacer II. Analysis of high efficiency range of cutting speed based on fractures of the cutting edge. Mokuzai Gakkaishi Journal of the Japan Wood Research Society 34(8): 676-681, 1988

Tool life in the cutting of wood by a super surfacer I. A proposed tool-life equation based on fractures of the cutting edge. Mokuzai Gakkaishi Journal of the Japan Wood Research Society 34(8): 669-675, 1988

Detection of wear degree of cutting tool by acoustic emission signal. Mokuzai Gakkaishi = Journal of the Japan Wood Research Society 38(9): 841-846, 1992

Fracture toughness and acoustic emission characteristics of wood II. Effects of grain angle. Mokuzai Gakkaishi = Journal of the Japan Wood Research Society 38(4): 342-349, 1992

Acoustic-emission diagnosis of the quality of the material of a wood-cutting tool. Lesnoi Zhurnal 6: 73-77, 1985

Application of acoustic emission measurement to sensing of wear and breakage of cutting tool - Application des mesures de l'émission acoustique au contrôle de l'usure et de la rupture des outils de coupe. Bulletin of the Japan Society of Precision Engineering 17(3): 154-160, 1983

Acoustic emission characteristics in wood sanding, I. Effects of the grain sizes and the sanding times on acoustic emission in belt sanding. Mokuzai Gakkaishi = Journal of the Japan Wood Research Society 41(7): 647-651, 1995

Acoustic emission characteristics in wood sanding II. Effects of sanding pressure and sanding direction on acoustic emission in belt sanding. Mokuzai Gakkaishi = Journal of the Japan Wood Research Society 43(3): 280-284, 1997

Recognition of wood cutting conditions through cutting sounds I. Effects of tool system's stiffness and tool wear on the generation of sound in cutting parallel to the grain. Mokuzai Gakkaishi = Journal of the Japan Wood Research Society 39(5): 521-528, 1993