Home
  >  
Section 3
  >  
Chapter 2,984

The effect of liquid properties on spray formation by flat fan nozzles

Ellis, M.C.B.; Tuck, C.R.

Aspects of Applied Biology 48: 105-112

1997

ISSN/ISBN: 0265-1491
Accession: 002983469
The size distributions of spray droplets produced by an agricultural flat fan nozzle spraying a range of spray liquids, containing a blank emulsifiable concentrate formulation and one of 6 adjuvants, were measured. Measurements of surface tension of the spray liquids were also carried out. Photographs of spray formation showed that the mechanism of sheet disintegration is through perforation by the emulsion droplets.

PDF emailed within 1 workday: $29.90




Related References

Sarker, K.U.; Parkin, C.S.; Williams, B.J. 1997: Effect of liquid properties on the potential for spray drift from flat-fan hydraulic nozzles BRITISH CROP PROTECTION COUNCIL Author The Brighton crop protection conference: Weeds, Vols 1-3 555-560
Kluza, P.A.; Kuna-Broniowska, I.; Parafiniuk, S. 2019: Modeling and Prediction of the Uniformity of Spray Liquid Coverage from Flat Fan Spray Nozzles Sustainability 11(23): 6716
Butler Ellis, M.C.B.tler; Tuck, C.R.; Miller, P.C.H. 1997: Emulsions and their effect on spray formation and droplet size with agricultural flat fan nozzles BRITISH CROP PROTECTION COUNCIL Author The Brighton crop protection conference: Weeds, Vols 1-3 561-566
Chen, C.T.; Maa, J.R.; Yang, Y.M.; Chang, C.H. 2001: Drop formation from flat tip nozzles in liquid-liquid system International Communications in Heat and Mass Transfer 28(5): 681-692
Selcan, Z. 1984: Are rotating nozzles better than flat spray nozzles? Landtechnische Zeitschrift 35(7): 1087-1090
Ganzelmeier, H.; Luders, W. 1982: Deposition of spray drops from flat spray and swirl nozzles on to artificial plants Landbauforschung Volkenrode 34(6): 86-90
Wijesuriya, S.D.E. 1992: Uniformity of spray distribution in flat fan nozzles Beitrage zur Tropischen Landwirtschaft und Veterinarmedizin 30(4): 357-362
Spanoghe, P.; Steurbaut, W.; Van der Meeren, P. 2001: The influence of adjuvants on flat fan spray nozzles Mededelingen 66(4): 47-51
Spanoghe, P.; Steurbaut, W.; Meeren, P. van der 2001: The influence of adjuvants on flat fan spray nozzles Mededelingen van de Faculteit Landbouwwetenschappen - Rijksuniversiteit Gent 66(4): 47-51
Rhee, J.; Young, B.W.; Bode, L.E. 1990: Transport of spray droplets from flat-fan nozzles Paper American Society of Agricultural Engineers 90-1001: 23 pp.
Zhou, Q.; Miller, P.C.H.; Walklate, P.J.; Thomas, N.H. 1996: Prediction of spray angle from flat fan nozzles Journal of Agricultural Engineering Research 64(2): 139-147
Czaczyk, Z.; Kramer, H.; Kleisinger, S. 2001: Influence of wear on spray quality of flat fan nozzles Parasitica 57(1/3): 69-73
Nystrom, P. 1981: Double-outlet and conventional flat spray nozzles Weeds and Weed Control 22nd Swedish Weed Conference, Uppsala, 1981 (1. Reports): 106-116
Schegk, C.D.; Loffler, F.; Umhauer, H. 1986: Drop-size distributions produced by flat-spray nozzles Particle Characterization 3(1): 14-19
Dorr, G.J. 1990: The effect of orientation and fan angle on spray deposition by flat fan nozzles Agricultural engineering conference 1990 Proceedings of a conference held in Toowoomba, Australia, 11-14 November 1990: 30-32
Cunha, J.P.A.R. da; Ruas, R.A.A. 2006: Volumetric distribution of air induction twin flat spray nozzles Pesquisa Agropecuaria Tropical 36(1): 61-66
Lacerda, A.L.S. 2001: Spray distribution pattern of flat fan tip (8002) at different spacing between nozzles Planta Daninha 19(3): 457-461
Kohsiek, H.R.etz, S. 1981: Investigations of drift using flat-spray nozzles in a wind tunnel Mitteilungen Biologische Bundesanstalt fur Land und Forstwirtschaft Berlin Brunswick: (203) 288-289
Groner, H.N.yken, W.S.ur, R. 1981: Investigations of flat-spray and low-pressure nozzles with fungicides and herbicides Mitteilungen Biologische Bundesanstalt fur Land und Forstwirtschaft Berlin Brunswick: (203) 218-219
Yeo, D. 1959: Droplet size distributions from flat-spray nozzles fitted to aircraft J.agric.Engng Res 4(2): 93-9