Effect of dilute and dense phase operating conditions on bed-to-wall heat transfer mechanism in a circulating fluidized bed combustor
Nirmal Vijay, G.; Reddy, B.V.
International Journal of Heat and Mass Transfer 48(16): 3276-3283
2005
ISSN/ISBN: 0017-9310 Accession: 075021818
PDF emailed within 1 workday: $29.90
Related References
Luan, W.; Bowen, B.D.; Lim, C.J.; Brereton, C.M.H.; Grace, J.R. 2000: Suspension-to-membrane-wall heat transfer in a circulating fluidized bed combustor International Journal of Heat and Mass Transfer 43(7): 1173-1185Golriz, M.R. 1996: Suspension-to-wall heat transfer in a 12-MWth circulating fluidized-bed combustor International Journal of Energy Research 20(7): 569-579
Gnanapragasam, N.V.; Reddy, B.V. 2009: Numerical modeling of axial bed-to-wall heat transfer in a circulating fluidized bed combustor International Journal of Heat and Mass Transfer 52(7-8): 1657-1666
Gnanapragasam, N.V.; Reddy, B.V. 2008: Numerical modeling of bed-to-wall heat transfer in a circulating fluidized bed combustor based on cluster energy balance International Journal of Heat and Mass Transfer 51(21-22): 5260-5268
Ozen, G.; Aydin, F.; Selçuk, N. 2016: Radiative Heat Transfer in the Dilute Zone of an Air-Fired Circulating Fluidized Bed Combustor and Its Oxy-Fired Retrofit Combustion Science and Technology 188(4-5): 730-744
Basu, P.; Nag, P.K.; Chen, B.H.; Shao, M. 1987: Effect of operating variables on bed to wall heat transfer in a circulating fluidized bed Chemical Engineering Communications 61(1-6): 227-237
Nag, P.K.; Mukhtar Sallam, A.L.I. 1992: Effect of operating parameters on bed-to-wall heat transfer in a high temperature circulating fluidized bed International Journal of Energy Research 16(1): 61-73
Ziegelhoeffer A.; De Jong J.W.; Ferrari R.; Turi Nagy L. 1989: Suspension-to-Surface heat transfer in a circulating-fluidized-bed combustor Aiche Journal 35(10): 1685-1691
Gui Young Han; Yong Jun Cho 1999: Radiative heat transfer in a circulating fluidized bed coal combustor Powder Technology 102(3): 266-273
Nag, P.K.; Sallam Ali, M.; Reddy, B.V. 1993: Heat transfer in a circulating fluidized bed combustor burning indane gas Indian Journal of Technology 31(1): 9-12
Abdelmotalib, H.M.; Ko, D.G.; Im, I. 2016: A study on wall-to-bed heat transfer in a conical fluidized bed combustor Applied Thermal Engineering 99: 928-937
Yumin, C.H.A.N.G.; Yufu, L.O.; Mayyenn, C.H.E.N. 1990: Heat transfer measurements of a 1.0 ton-steam/HR circulating fluidized-bed combustor burning Taiwan coals Particulate Science and Technology 8(3-4): 199-208
Jin Hee Jeon; Sang Done Kim; Seung Jae Kim; Yong Kang 2008: Combustion and heat transfer characteristics in a square internally circulating fluidized bed combustor with draft tube Fuel 87(17-18): 3710-3713
Petitjean, C.; Crabol, J. 1991: Mesures des coefficients d'échange de chaleur dans un milieu diphasique en transport pneumatique - Measurements of heat transfer coefficients from the dilute phase of a circulating fluidized bed Revue Generale de Thermique 30(358): 614-620
Winaya, N.S.; Basu, P.; Reddy, B.V. 2003: Experimental investigations on heat transfer from suspension to impact separators in the riser column of a circulating fluidized bed combustor International Journal of Heat and Mass Transfer 46(1): 71-75
Cho, Y.J.; Kim, S.D.; Han, G.Y. 1996: Bed-to-wall heat transfer characteristics in a circulating fluidized bed Korean Journal of Chemical Engineering 13(6): 627-632
Daming, S.H.I.; Nicolai, R.; Reh, L. 1998: Wall-to-bed heat transfer in circulating fluidized beds Chemical Engineering and Processing 37(4): 287-293
Fox, W.B.; Grewal, N.S.; Moen, D.A. 1999: Wall-to-bed heat transfer in circulating fluidized beds International Communications in Heat and Mass Transfer 26(4): 499-508
Jiansheng, Z.H.A.O.; Grace, J.R.; Lim, C.J.; Brereton, C.M.H.; Legros, R. 1994: Influence of operating parameters on NOx emissions from a circulating fluidized bed combustor Fuel (Guildford) 73(10): 1650-1657
Basu, P.; Thuong, N.G.O. 1993: Effect of some operating parameters on heat transfer to vertical fins in a circulating fluidized bed furnace Powder Technology 74(3): 249-258